T-Drill

Advantages Only one brazed joint instead of three soldered joints Less wasted material Less inventory of fittings No cutting of run tube Shorter installation time - up to 65% Better quality of joint - less leakages
T-60 TEE-Forming System for Copper TEE sizes 10 - 54 mm (1/2" to 2") Max run tube 108 mm (4") M, L or K Copper TEE Forming time 15 - 60 seconds depending on TEE size
T-60 Collaring System for Stainless Steel Tube Collar sizes O.D. 20 - 51 mm (3/4" to 2") Max run tube 114,3 mm (4") Wall thickness 1.2 - 2.0 mm (Schedule 5) Collaring time 5 - 10 minutes Get T-60 Brochure (pdf format size: 290 Kb. It may take few minutes to download)
Plus 100 Attachment for Copper Powered by T-60 Power unit Collar sizes up to 114,3 mm (4") Max run tube 219,1 mm (8") Collaring time appr. 15 minutes

Fast, safe and easy pipe cutting

Steel and cast-iron pipes are usually cut with an angle grinder, a tool that was not originally designed for cutting pipes. An angle grinder is a rather slow and inexact tool when used for pipe cutting. It is a fire risk, and can cause material damage and occupational hazards. The innovative Pipe Cutting System 8 solves most common pipe cutting problems.

Square cuts

During pipe cutting, the Pipe Cutting Systems 8 fits firmly on the pipe and the saw blade is always in the correct position. There is no need for steering. The T-DRILL Pipe Cutting System 8 leaves the cut edges straight and square, with a smooth surface. Sparks and dust are kept to a minimum. The cut is ready for welding with no further preparation needed.

User benefits

The T-Drill Pipe Cutting System 8 is lightweight, ergonomic and safe to use, even in confined spaces, as the weight of the machine lies on the pipe during cutting. There is no need to lift pipe as they can be cut at ground level. Pipe cutting with an angle grinder or band saw is much more dangerous, exhausting and dirty than with the Pipe Cutting System 8

No damage or fire risk in the working environment

The need for protection within the working environment is much less with the Pipe Cutting System 8, when compared with an angle grinder or band saw. The chips caused by pipe cutting cool down quickly, and fall very close to the cutting site. Work safety will be enhanced, as the T-DRILL Pipe Cutting System 8 does not require any special skills.

Versatile

The Pipe Cutting System 8 has a very wide cutting range. It is the only machine that is able to cut pipes between 1” NPS and 8” NPS in diameter. All commonly used pipe materials can be cut with T-DRILL Pipe Cutting System 8.

Saw blades

Pipes

The T-DRILL Pipe Cutting System 8 is able to cut pipe between 1” NPS and 8” NPS in diameter.

Maximum pipe wall thickness can be .320” in steel, and .450” in plastic.
All commonly used pipe materials, such as mild steel, stainless steel, copper, cast-iron and plastic can be cut with the T-DRILL Pipe Cutting System 8.

Easy and safe pipe cutting

Cutting pipe with the T-DRILL Pipe Cutting System 8 is very easy to learn.
There is no need to lift heavy pipe, as they can be cut easily on the ground.
The T-DRILL Pipe Cutting System 8 fits firmly on the pipe during cutting, allowing the user to easily control the machine.

Safe working environment

The need for protection within the working environment is minimal, because Pipe Cutting System 8 does not cause a hot shower of sparks like an angle grinder does.
It is safer, as the chips caused by pipe cutting cool quickly, and fall to ground very close to the cutting site.

Easy to use even in confined spaces

The workspace required for pipe cutting with the Pipe Cutting System 8 is approximately three feet.
Adjusting the machine for different diameter pipes and installing on the pipe is fast and easy.

Handy and quick

Cutting small diameter pipe in exact length is also handy and quick on a bench.
The T-DRILL Pipe Cutting System 8 saw blade is quick and easy to change.
Straight cut and fine edges are immediately ready for joints, or welding.

T-DRILL pipe holders

With the assistance of the T-DRILL pipe holder, you can cut pipe even faster and easier, especially with heavy pipe. The T-DRILL pipe holder set includes one large and two small holders.